Turbochargers have become a staple in both modern performance and efficiency-focused vehicles. Even BMW, a historic champion of natural aspiration, especially in ///M cars, has made the switch to boost! Turbos provide more power by forcing extra air into the engine, allowing for better combustion and increased horsepower. However, if you have driven a turbocharged car, especially older models, you might have noticed a delay between pressing the accelerator and feeling the surge of power. That delay is known as turbo lag.
Turbo lag refers to the time it takes for a turbocharger to deliver increased power after the driver hits the gas pedal. Turbos rely on exhaust gases to spool up (spin) the turbine wheel, which then spins the compressor wheel and pressurizes charge air on the intake side. At low engine speeds, there is not enough exhaust flow to spin the turbo quickly, resulting in a noticeable delay before boost pressure builds up and power increases.
Several factors contribute to turbo lag:
Automakers and tuners use various methods to reduce turbo lag and improve throttle response. Here are some of the most effective:
Smaller turbos have less rotational inertia and require less exhaust flow to spool up. While they produce less peak power than larger turbos, they offer quicker response and lower lag. This is why many factory turbocharged engines prioritize smaller turbos for daily-driven street use. Be careful not to choose too small of a turbine housing and wheel, which can significantly reduce performance and output!
Twin-scroll designs separate exhaust pulses coming from different cylinders, allowing more efficient use of exhaust energy. This helps the turbo spool faster and reduces lag without sacrificing top-end power. The downside is that twin-scroll set-ups require special exhaust manifolds and turbine housings, which are not as common as single scroll components, and are often more expensive.
Common in diesel engines and increasingly in performance gas engines, variable geometry turbos adjust the angle of the vanes inside the turbine to optimize exhaust flow at various engine speeds. This allows for fast spool at low RPM and strong performance at high RPM, significantly reducing lag. The downside is these are far more complex in design, operation, and cost than standard turbochargers.
Some setups use two turbochargers: one small (for low RPM) and one large (for high RPM). In sequential setups, the smaller turbo spools quickly to reduce lag, then the larger turbo takes over as RPM increases. This setup balances low-end responsiveness with high-end power. The downside is complexity of exhaust manifold design, increased weight, and additional cost of two turbos.
Used mostly in racing applications, anti-lag systems keep the turbo spinning even when the throttle is closed. This is done by injecting fuel and air into the exhaust manifold, creating violent combustion to maintain turbo speed. While highly effective, ALS systems can be harsh on components and are not street-friendly. ALS set-ups also require aftermarket engine management and a competent tuner.
Some newer vehicles feature electric turbochargers or electric superchargers to eliminate lag entirely. These systems use an electric motor to spin the compressor independently of exhaust gases, offering instant boost until the conventional turbo takes over. While there are more components to fail and or repair, these will become more common as manufacturers try to blur the line between natural aspiration and forced induction.
Modern engine management systems can be tuned to increase throttle sensitivity, adjust boost thresholds, and minimize lag through software. Tuning can also reduce delays in throttle-by-wire systems and optimize boost onset timing. It is important to work with a qualified tuner who has the experience and expertise to recalibrate your ECU, factory original or aftermarket.
Shortening and simplifying the piping between the turbo and the intake manifold decreases the amount of air that must be pressurized and moved. Less volume means quicker response and less lag. Think of this in terms of water flowing through a garden hose. The smaller the diameter, the greater the pressure, and the shorter the length, the quicker the ouput!
Turbo lag, a natural byproduct of forced induction, does not have to be a major drawback. Thanks to advancing technology and smart engineering, it is possible to enjoy the benefits of turbocharging with minimal delay. Whether you are buying a car or building a custom setup, understanding and mitigating turbo lag can lead to a more responsive and enjoyable driving experience. Modern turbochargers, components, and tuning solutions have made both OEM and aftermarket boost better than ever!
Get news from VAC Motorsports, Inc. in your inbox.
Email*
By submitting this form, you consent to receive marketing emails from VAC Motorsports, Inc., 2501 Snyder Ave, Philadelphia, PA, 19145, US, http://www.vacmotorsports.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link at the bottom of every email. Emails are serviced by Constant Contact.